DIY Resin Key Holder with Message!想いを込めて♡メッセージ入りレジンキーホルダー

by C CHANNEL Art&Study DIY Crafts Handmade
1841

DIY Resin Key Holder with Message!想いを込めて♡メッセージ入りレジンキーホルダー

 

Materials Heart type silicon mold UV LED resin HARD Alphabet beads Heart Parts gloves tweezers UV light Random aurora flakes Toning palette Toning stick Nipper Hand drill Eye pin Flat pincersRound jump ring Key holder parts Steps 1 Pour resin in silicon mold until about 8th minute2 Arrange the parts and beads Please arrange the characters backwards so that the alignment of characters is correct when viewed from the front side3 Cure with UV light4 Mix the resin and aurora flakes and pour into silicon mold until 8th minute5 Put the resin cured before on top and cure6 Remove it from the mold and cut the protruding resin7 Open a hole8 Apply resin to eye pin insert it in the hole and harden it9 Complete after connecting key holder parts プレゼントにもぴったり シンプルだけど可愛いレジンキーホルダーです 必要なもの ハート型シリコンモールド UV LEDレジン 星の雫 HARD アルファベットビーズ ハートパーツ 手袋 ピンセット UVライト 乱切りオーロラ 調色パレット 調色スティック ニッパー ピンバイス 9ピン 平ヤットコ 丸カン キーホルダー金具 手順 1 シリコンモールドにレジンを8分目くらいまで流し込む2 ビーズとパーツを並べる 表から見たときに文字の並びが正しくなるよう 上下左右反対に配置してください3 UVライトで硬化させる4 レジンと乱切りオーロラを混ぜ シリコンモールドに8分目くらいまで流し込む5 先ほど硬化させたレジンを上から被せて硬化させる6 モールドから外し はみ出たレジンをニッパーできる7 ピンバイスで穴を開ける8 9ピンにレジンをつけ 穴に差し込み硬化させる9 キーホルダー金具を接続したら完成 気泡ができないよう ビーズはゆっくり入れるのがコツです

 

 


夏厨 232 下雨天,身边有只胖猫,一碗热气腾腾的豚骨拉面,...

  • by 夏厨 | Summer Kitchen 1529

面食主义者的最爱,汤浓味美叉烧豚骨拉面,让胃不再单调 下雨天你最想吃什么 园长我选择一碗豚骨叉烧拉面 再加一个溏心蛋 熬了3个小时的浓郁汤底 味道和外面用浓汤宝香精不一样 特别是加了苹果汤头更香甜清爽 要是每个下雨天都能这样饱饱地吃上一大碗 宅得太享受了

Funniest Winter Animal Video C...

  • by Funny Pet Videos 1929

Winter is Coming! So lets start off this season with a brand new compilation of the cutest and funniest animals playing in the sno...

りゅうスケッチ_((Ф(.. )カキカキ 暑ーい夏の昼下が...

  • by mixjam11 1122

長かった梅雨、各地で甚大な被害をもたらせましたが、皆さんの地域は大丈夫でしたか? 梅雨が開けた途端、今度は茹だるような暑さになっちゃいましたね(;´д`)熱中症にはくれぐれもお気を付けてくださいね。 そういうオイラは昼間は極力室内に閉じこ持って生活しています(...